This guide will walk you through the Wavlink AC600 setup. Wavlink AC600 is a dual-band outdoor wireless range extender. It includes a high-power amplifier to eliminate dead zones in your area. The Wavlink AC600 has a maximum speed of 600mbps. The Wavlink AC600 has the ability to repeat and expand its range over a long distance. This allows you to use a router, an access point, and a repeater.
The following are required for Wavlink AC600 setup:
- A more reliable power source.
- Username and password for Wavlink
- It is necessary to have a smart device with a browser that supports it.
Directions for the Wavlink AC600 setup:
- Unbox and set up your gadget.
- Connect the AC600 to an electrical outlet.
- Take out your smart gadget of choice.
- Install your internet-connected gadget.
- Choose a browser.
- Enter 192.168.10.1 as the address.
- Enter your name and administrator password next.
- Please click here to login.
- To configure your Wavlink AC600 extension, follow the on-screen instructions. If you have successfully connected your extender to the router but are still unable to connect to the internet, the Wavlink AC600 firmware may need to be upgraded.
Wavlink AC600 setup using WPS button
Follow these steps to configure the Wavlink AC600 through WPS (wireless protected setup). WPS is the most straightforward method for expanding your host network and setting your Wavlink AC600.
Here are some ideas for Wavlink AC600 setup using WPS method:
- To begin, position your Wavlink wifi extender near the router.
- Switch on your Wavlink AC600.
- Allow the LED light to turn completely green and stable.
- Press the WPS button on both your AC600 and router.
- A green light will blink now.
- Allow a few seconds for your extender to properly sync with your home wifi router.
Finally, you’ve completed the Wavlink AC600 setup using WPS procedure. If you have any questions about your Wavlink extender, please contact us via chat or phone.
Firmware update for Wavlink AC600?
Look for updates to your Wavlink AC600 Firmware that provide functionality, upgrades, and bug fixes for your Wavlink AC600 extender.
To upgrade the firmware on your Wavlink AC600, follow the instructions below:
- Navigate to your web browser.
- Enter wifi.wavlink.com in the URL field.
- Use your regular password to fill in the fields.
- Click the login icon to log in.
- After that, install the most recent Wavlink AC600 firmware version.
- When you’re finished, click the setup button.
- When you upgrade the firmware on your extender, it will reboot.
If you are unsure how to upgrade the Wavlink AC600 extender firmware, or if you are encountering problems with your AC600 extender, please contact our experienced staff for assistance.
How to reset Wavlink AC600?
To reset your AC600, perform the following steps:
- Start by turning on any smart device.
- Connect your Wavlink AC600 and router using ethernet cable.
- Look for the reset button hole on the back of the AC600.
- To reset your router, press and hold the reset button for a few seconds.
- Insert a pointed pin or something similar into the hole for the reset button.
- Hold it in place for 8-10 seconds.
This paper will walk you through the steps necessary to reset your Wavlink AC600 extender.
How to reset the Wavlink AC600 using a web browser?
Go to wifi.wavlink.com to reset your Wavlink AC600 extender:
- To begin, launch your computer’s web browser.
- Then, in your browser’s address bar, type wifi.wavlink.com or 192.168.2.1.
- To gain access to your extender’s dashboard, simply enter your username and password.
- Then, on the extender’s login screen, pick advanced from the drop-down box.
- An extender information tab will appear on your screen, from which you must select the factory default setting reset option.
- The reset of your extender has now been completed successfully.
How do I login to my Wavlink AC600?
Follow the steps below to log in to your Wavlink AC600 extender:
- Check to see if the Wavlink router is operational. To view the configuration page, you must first connect to the Wavlink router’s network. Connect to the network via an Ethernet or Wi-Fi connection as a consequence.
- You can connect over Ethernet if you don’t know the username and password for your Wavlink router’s wireless network. There will be no need to put any username or password.
- Open a web browser on your PC and navigate to the address bar. To access the web interface of your Wavlink router, enter the IP address 192.168.10.1 and press enter on your keyboard.
- You will then be asked to input your login information. Fill up the relevant sections with your Username and Password, then click the ‘Sign in’ button.